new early hemi manifolds
Moderators: scottm, TrWaters, 392heminut
new early hemi manifolds
Here's a pic of the first Desoto 6x2. It's an EELCO brand.
http://www.eelco-usa.com/index.php?cPat ... a3613e604a
We have a casting date of 9/15 on the 3x2 dual plane for the chrysler hemi manifold.
We have had a few request for the single 4bbl for the Desoto and Dodge but nobody has commited to an order. If you want them; call us direct at 503-651-3352 or email sales@eelco-usa.com
If you go to the site; wander around a bit. There is a lot to see on there and it gets added to alomost daily. Take care.
http://www.eelco-usa.com/index.php?cPat ... a3613e604a
We have a casting date of 9/15 on the 3x2 dual plane for the chrysler hemi manifold.
We have had a few request for the single 4bbl for the Desoto and Dodge but nobody has commited to an order. If you want them; call us direct at 503-651-3352 or email sales@eelco-usa.com
If you go to the site; wander around a bit. There is a lot to see on there and it gets added to alomost daily. Take care.
-
- Posts: 433
- Joined: Sat Dec 01, 2001 6:00 pm
- Location: Maryland
Sounds great, on the Chrysler 3X2 manifolds, couple of questions:
Are they sand cast aluminum?
What bolt style carb base are they setup to take?
Are you going to offer/sell the carbs/linkeage/aircleaner assemblies for them?
Are the flanges large enough to cover the rectangular port heads' center heat exchanger?
Are they plumbed for water crossover in the manifold, with a thermostat in the manifold, to eliminate the external water crossover?
Do you have the facilities to polish the manifolds and a cost established for the polishing?
Could you deliver 5 manifolds/carb setups/linkeage/aircleaners units by Nov 1, 2006?
PS: Good Luck with the venture.
Are they sand cast aluminum?
What bolt style carb base are they setup to take?
Are you going to offer/sell the carbs/linkeage/aircleaner assemblies for them?
Are the flanges large enough to cover the rectangular port heads' center heat exchanger?
Are they plumbed for water crossover in the manifold, with a thermostat in the manifold, to eliminate the external water crossover?
Do you have the facilities to polish the manifolds and a cost established for the polishing?
Could you deliver 5 manifolds/carb setups/linkeage/aircleaners units by Nov 1, 2006?
PS: Good Luck with the venture.
All manifolds are sand cast aluminum. The water crossover and thermostat housing is not part of this design but the pattern can be modified to do so. The flanges are large enough to cover the heat exchangers.
We have been producing the linkage and accessories for several years now and can be seen at our site www.eelco-usa.com.
The manifolds are capable of being ordered and drilled for either 3 or 4 bolt carbs.
We do have a polisher in Southern California that we recommend and can ship direct to them for you.
We have a pour date of 9/15 and tooling will follow. This usually allows shipping in 2-3 weeks after the first run is complete.
November will be no problem at this time. However; orders are being taken now. No deposit is necessary but we will ship in the order they are recieved.
We have been producing the linkage and accessories for several years now and can be seen at our site www.eelco-usa.com.
The manifolds are capable of being ordered and drilled for either 3 or 4 bolt carbs.
We do have a polisher in Southern California that we recommend and can ship direct to them for you.
We have a pour date of 9/15 and tooling will follow. This usually allows shipping in 2-3 weeks after the first run is complete.
November will be no problem at this time. However; orders are being taken now. No deposit is necessary but we will ship in the order they are recieved.
No pics will be posted until we have the first manifold poured. it is in the pattern process now.
Pre-orders are 370.00 with an expected list price (retail of 425.00) You will save 50.00 by ordering now.
You will be contacted when they are ready to ship for payment. We are not asking for money .Just a commitment to purchase.
Pre-orders are 370.00 with an expected list price (retail of 425.00) You will save 50.00 by ordering now.
You will be contacted when they are ready to ship for payment. We are not asking for money .Just a commitment to purchase.
Re: new early hemi manifolds
===================retro wrote:Here's a pic of the first Desoto 6x2. It's an EELCO brand.
http://www.eelco-usa.com/index.php?cPat ... a3613e604a
We have a casting date of 9/15 on the 3x2 dual plane for the chrysler hemi manifold.
We have had a few request for the single 4bbl for the Desoto and Dodge but nobody has commited to an order. If you want them; call us direct at 503-651-3352 or email sales@eelco-usa.com . If you go to the site; wander around a bit. There is a lot to see on there and it gets added to alomost daily. Take care.
Wow! That is a BEAUTIFUL piece! Well done! My hat is off to you and Eelco. I'm sure it will be well recieved once word starts geting around that they're available. I hope this will be the start of many new manifolds for a whole variety of other so called "obsolite" engines. Thank you for doing this.
mart
===========================
The Desoto 6x2 is finished and we are shipping them now. We have had far more requests for the 3x2 than any other intake so we may head that direction first. We are taking names only at this point and will call for payment when they are ready to ship. If you want parts made for your Desots, Here's your chance. Thanks for the opportunity.
DeSoto 341 Manifold
PLEASE produce a single four barrel High performance intake for the DeSoto 341.
291 and 330 DeSoto intakes
i
Need 4x2 inline intake for either a 291 or 330 DeSoto
Want Fenton or Edmunds speed equipment for 230 inch flat 6 Dodge engines
Need 42 Dodge trim pieces
Need good windshield frame and hood center strip for 1 ton 1937 Dodge truck
Want Fenton or Edmunds speed equipment for 230 inch flat 6 Dodge engines
Need 42 Dodge trim pieces
Need good windshield frame and hood center strip for 1 ton 1937 Dodge truck
Re: new early hemi manifolds
i am looking for a intake manifold WC3D, i understand how rare they are but just putting out there if anyone knows of one. That being said reading the post of years ago it sounded like they are being poured again. i know the mold was thrown away when Holly purchased Weiland but just curious about this pour and who is doing it
Re: new early hemi manifolds
DeSoto won't fit Chr. See 1 occaisonaly on E-Bay
Re: new early hemi manifolds
Is 'retro' still around? ...anyone have details as to what happened to eelco?
www.qualityengineeredcomponents.com
Early Hemi Parts and Pieces,
INVENTORY CLEARANCE IN PROGRESS. See website for details.
Early Hemi Parts and Pieces,
INVENTORY CLEARANCE IN PROGRESS. See website for details.
Re: new early hemi manifolds
Hadn't heard of "retro". There were/was a thread on the HAMB about all the bad behavior of the owner/ guy who bought EECO, that was a number of years ago. Haven't heard of them since.
Re: new early hemi manifolds
by retro » Fri Nov 17, 2006 8:48 pm
...maybe 'retro' means something else....
...maybe 'retro' means something else....
www.qualityengineeredcomponents.com
Early Hemi Parts and Pieces,
INVENTORY CLEARANCE IN PROGRESS. See website for details.
Early Hemi Parts and Pieces,
INVENTORY CLEARANCE IN PROGRESS. See website for details.
Re: new early hemi manifolds
Looking back, I see "Retro" must have been EELCO's owner or an associate. They got hammered on the HAMB, apparently trying to do so much different stuff they wern't getting anything done.